Draught beer system guide: serve perfect beer without waste
The tower is what guests see, but the cooler, the gas and clean lines decide what ends up in the glass. This is the practical routine we teach bar teams – from switching on the cooler to fixing foamy beer.

1. The cooler and the ice bank
The cooler is the heart of the system. It needs free air circulation – never build it tightly into a closed cabinet.
- Fill with water first. Before starting the compressor, fill the tank with clean water so that the beer and gas coils are completely covered.
- Allow 6–8 hours. The cooler needs this long to build a stable ice bank. Pouring earlier means warm beer and immediate, aggressive foaming.
- Thermostat. The usual setting for standard beers is 1–3 °C.
2. Gas: CO2 and nitrogen
Gas pushes the beer out of the keg and keeps its carbonation stable, so the pressure setting on the regulator must be precise.
- Working pressure is between 1.5 and 2.5 bar in most installations. Too low and CO2 breaks out of the beer in the lines (gaps and foam); too high and the beer becomes over-carbonated.
- Safety. A high-pressure cylinder must always be secured against falling with a chain or a wall bracket.
Changing the gas cylinder
- Close the main valve on the empty cylinder.
- Release the gas left in the line until the working gauge reads zero.
- Unscrew the high-pressure hose and check the washer – a damaged or missing washer is the most common cause of losing a full cylinder overnight.
- Connect the new cylinder and tighten the hose firmly with a spanner.
- Open the main valve slowly and set the working pressure on the regulator.
3. Pouring and the compensator
Open the tap with one decisive, full movement – half-open taps make foam.
- Compensator. The lever on the side of the tap throttles the flow. If the beer foams too much, increase the resistance; if the stream is too weak, reduce it gradually. Quality taps with a compensator let you tame even highly carbonated craft beers.
- Keg handling. Never connect a keg that has just been delivered and shaken. Pre-chill kegs in a cold room – it relieves the cooler and stabilises dispense. Use FIFO: always serve the oldest delivery first.
- Date the keg. Write the date and time of opening on the keg with a waterproof marker when you connect the coupler.
- Coupler. Use the correct, clean coupler type for the keg (A, S or M system are the most common in Europe).
4. Line cleaning: how often?
Dirty lines spoil the taste, sour the beer and waste product through foaming. The interval depends on the beer and the cooling:
| Installation | Interval | Method |
|---|---|---|
| Pasteurised, filtered lager; glycol-cooled python | Every 4–6 weeks | Recirculation cleaning (CIP) with a service pump |
| Craft: unpasteurised, unfiltered, dry-hopped, fruit or sour beers | More often, by style – check visually | Chemical + mechanical: sponge balls pushed through the lines, rotating cleaners |
| Kegerators, mobile bars, low turnover | At every keg change (max. every 30 days) | Chemical flush + full dismantling of tap and coupler |
Golden rules
- Rinse with water at the end of each shift or when changing kegs, so beer and yeast do not dry inside the lines.
- Rotate the chemistry. Use an alkaline cleaner for biofilm and, every few months, an acid cleaner to remove beer stone (calcium oxalate).
- Taps and spouts daily. Parts in contact with air should be sanitised and brushed at the end of every shift to stop mould and fruit flies.
- Keep it cold. The warmer the cellar, the faster bacteria grow. Stable, low temperatures reduce how often the lines need cleaning.
- Keep a cleaning log. Food-safety inspectors in most EU countries expect a record of line cleaning as part of your hygiene (HACCP) procedures: date, signature and the cleaning product used.
5. Troubleshooting
The beer foams too much
- Cooling: is the cooler switched on and has it had enough hours to build the ice bank? Are the coils covered with water (wet coolers)? Warm or shaken kegs always foam.
- CO2 pressure: check the cylinder and the regulator – the working pressure should be 1.5–2.5 bar.
- Dirty lines: biofilm causes foaming. Check the date of the last cleaning in your log.
- Leaks: listen for hissing gas, especially at the coupler and the quick connectors on the cooler. Any air drawn into the system makes the beer foam.
- Coupler and fitting: remove the coupler and check that the keg fitting and washers are not covered with dried beer.
- Other causes: a damaged keg fitting, worn coupler seals, kegs that were frozen or overheated in storage, or a faulty batch.
No beer comes out of the tap
- Gas: is the cylinder valve fully open and does the regulator show working pressure?
- Coupler: is it the right type, and is the handle pushed down and locked on the keg?
- Lines and tap: check the beer hose for kinks or a door trapping it, and make sure the compensator is not fully closed.
- FOB stop: if you have a foam-on-beer detector, reset and vent it after connecting a new keg – an active FOB stop cuts the flow completely.
FAQ
What CO2 pressure should a draught beer system have?
In most installations the working pressure is 1.5–2.5 bar. Too low causes foam and gaps in the line, too high over-carbonates the beer.
How often should beer lines be cleaned?
Every 4–6 weeks for pasteurised beer with glycol cooling, more often for unpasteurised craft beer, and at every keg change for kegerators and mobile bars.
Why does my draught beer foam so much?
The most common causes are warm or shaken kegs, a cooler without a full ice bank, wrong CO2 pressure, dirty lines and air leaks at the coupler or connectors.
More guides
- Bowling club, North Macedonia: Columbus P with bowling-pin tap handles
- How to choose a copper beer tower for your bar
- How to clean a copper beer tower
- Four Points by Sheraton Wrocław: custom 6-tap copper beer tower
- Four Points by Sheraton Poznań: custom 6-tap Limbus T with pipes to the ceiling
- Brovar 16, Pszczyna: Saaz copper beer tower with LED medallions
- Manufaktura, Rzeszów: Columbus copper bridge tower with 6 taps
- Saaz Marine: 12-tap copper beer tower in a Masurian pizzeria
- Żywiec pizzeria: Limbus T copper beer tower with 6 taps
- Goczałkowice-Zdrój spa: a row of copper tap columns in the pump room
- Stadium VIP lounge, Łódź: 10 wall-mounted taps on polished brass discs
- Kraków: Limbus T copper beer tower with 6 taps and LED
- GVARNO, Zakopane: Limbus M copper multitap with 10 taps
- Nysa: Columbus P with 6 taps and a side-pull tap for Czech pilsner
- Brewery in Strzegom: Saaz with 8 taps and the python hidden in copper
- Hotel & spa: Columbus P with 7 taps and double-sided medallions
- Kraków restaurant: Columbus P bridge tower with 6 taps
- Miejscówka, Kraków: Limbus M multitap with 12 taps
- KIJ, Łódź: Limbus M with 10 taps and double-sided medallions
- Browar Przystań, Chorzów: two copper towers with LED next to the brewhouse
- Bielsko-Biała: beer lines from the ceiling in a copper pipe
- Kraków: Limbus M with 5 taps and medallions on the legs
- Władysławowo: Columbus P with 6 taps in a seaside bar


